AC Repair in Chadron, NE: How to Repair 3 Frequent Issues

There can be a couple of reasons why your central AC system won’t start: a tripped circuit breaker, inaccurate thermostat settings, a shut off switch or an overfull condensate drain pan.

Your air conditioner won’t run when you have a blown breaker.

To find out if one has gotten overloaded, go to your residence’s main electrical panel. You can spot this silver fixture on the wall in the basement, garage or closet.

• Ensure your hands and feet aren’t wet before you work on the panel or breakers.
• Look for the breaker marked “AC” and ensure it’s in the “on” position. If it’s tripped the lever will be in the in between or “off” position.
• Steadily shift the switch back to the “on” location. If it instantly triggers again, leave it alone and reach us at 308-832-4321. A fuse that keeps flipping may signal your home has electrical trouble.

If your thermostat isn’t giving a sign to your air conditioner to work, it won’t switch on.

The main step is checking it’s switched to “cool” and not “heat.” Otherwise your AC might not turn on. Or you might get. heated air coming from vents being the furnace is going instead.

If you rely on a traditional thermostat:

• Put in new batteries if the readout is empty. If the monitor is showing garbled letters, get a new thermostat.
• Check the correct mode is displaying. If you can’t update it, cancel it by lowering the temperature and hitting the “hold” button. This will force your AC to work if scheduling is incorrect.
• Test setting the thermostat 5 degrees colder than the space’s temperature. Your AC won’t cool if the thermostat is set the same as the space’s temperature.

Once your thermostat is set correctly, you should start getting refreshing air fast.

If you have a smart thermostat, including ones produced by Nest, Ecobee, Lux, Honeywell or Bosch, go to the manufacturer’s website for troubleshooting. If it still won’t work, reach us at 308-832-4321 for help.

Your cooling equipment typically has a power-cutting switch near its condenser. This switch is commonly in a metal box mounted on your house. If your air conditioner has recently been serviced, the device may have inadvertently been put in the “off” setting.

Condensate drain pans catch the extra liquid your air conditioner takes out of the air. This pan can be found either below or in your furnace or air handler.

When there’s a blockage or backed up drain, water can build up and initiate a safety feature to switch off your unit.

If your pan includes a PVC pipe or drain, you can clear the extra water with a special pan-cleaning tablet. You can purchase these capsules at a home improvement or hardware retailer.

If your pan has a pump, locate the float switch. If the switch is “up” and there’s moisture in the pan, you could need to replace the pump. Reach us at 308-832-4321 for support.

If your equipment is going but not cooling, its airflow might be obstructed. Or it could not have enough refrigerant.

Your equipment’s airflow can be restricted by a clogged air filter or dirty condenser.

A filthy filter can create numerous problems, such as:

• Lower airflow
• Icy refrigerant lines or evaporator coil
• Intermittent cooling
• Higher cooling costs
• Making your system break down faster

We propose changing flat filters every four weeks, and accordion filters every three months.

If you can’t recall when you last installed a new one, turn off your system fully and remove the filter. You can locate the filter in your furnace or air pump’s blower compartment. It might also be located in a connected filter box or wall-mounted return air grille.

Angle the filter up to the light. If you can’t see any light you certainly should get a new one.

Brush, plants and bushes can get in the way of your condensing equipment. This may limit its airflow, lower its energy efficiency and impact your comfort. Here’s a method you can follow to get your unit running properly again.

1. Shut off power completely at the breaker or outside device.
2. Get rid of yard debris around the unit. Once you’ve gotten rid of bigger clutter within a two-foot area, you can use a paint brush or vacuum to slowly remove dust from the unit’s fins. Kinked fins can also hurt performance, so you can attempt to reshape them with a small knife.
3. Use a hose nozzle to slowly remove gunk off the fins from inside the unit. Don’t get moisture on the fan motor.
4. Install the top again and restore the power.

When AC systems don’t have ample refrigerant, they’ll have to work much harder to remove heat and humidity from your house.

Here are several flags that your system is leaking refrigerant:

1. It takes a long time to lower the temperature in your rooms and you’re constantly decreasing the temperature on the thermostat.
2. Air conditioning moving through the registers isn’t as chilly as it should be.
3. You’re experiencing hissing or bubbling sounds when the air conditioning works.
4. Your evaporator coil is frosty on account of having trouble taking on humidity.

Think your unit is losing refrigerant? You need a authorized heating and cooling service specialist to take care of the leak and refill the right measurement of refrigerant in your equipment. Get in touch with us at 308-832-4321 for assistance.

When it seems like you’re not having enough chilled air, there’s potentially a clog or detachment somewhere in your cooling unit.

• The beginning step is checking your air filter. Replace it if it’s soiled.
• Then check the registers are free throughout your residence.
• If you’re still not getting adequate chilled air, you should have your ducts examined by a specialist like MPC Heating & Cooling. Your ductwork could need to be serviced or reconnected in difficult areas like your attic, basement or crawl space.